PPGI is pre-painted galvanized steel, normally using a zinc-coated substrate; PPGL is pre-painted aluminium-zinc-coated steel, commonly with a metallic coating of the 55% aluminium–zinc alloy type on the steel substrate. The main difference is the metallic coating beneath the paint, not the colour. Neither is automatically better for every roof, wall panel or formed part: compare the exposure, steel grade, metallic coating, paint system and forming requirements for the application.
IN THIS ARTICLE
PPGI vs PPGL: compare the whole coating system
| Item | PPGI | PPGL |
|---|---|---|
| Common name | Pre-painted galvanized iron or steel | Pre-painted galvalume or aluminium-zinc-coated steel |
| Typical metallic substrate coating | Zinc | Commonly 55% aluminium-zinc alloy |
| Visible finish | Selected paint system and colour | Selected paint system and colour |
| Key suitability question | Suitability of the complete specified system | Suitability of the complete specified system |
Scroll horizontally to read all columns
Commercial abbreviations are not complete product standards. The actual metallic coating must be identified separately. A conventional 55% aluminium-zinc coating is nominally 55% aluminium, 43.5% zinc and 1.5% silicon by mass; that description does not cover every aluminium-zinc or zinc-aluminium-magnesium product sold under loose trade names.
The metallic coating mass and the paint film thickness are separate requirements. Do not compare equal numbers in different coating systems as if they guaranteed equal thickness or equal service life.
Which is better for roofing or cladding?
Start with the building specification and exposure, not a blanket ranking. Coastal salt, industrial pollutants, standing water, cut edges, fasteners and contact with other materials can affect performance. A roof's geometry, drainage and maintenance also matter. The coating manufacturer's application guidance identifies the conditions covered by the particular system.
A description that says only “PPGL, blue” cannot establish roof suitability. It omits the substrate grade, metal coating mass, paint chemistry, film build and underside protection. Equally, “PPGI” does not mean a product is unsuitable: a correctly specified system may meet the application. Approve the proposed complete construction against the project requirements.
For roll-forming, confirm the steel grade and mechanical properties, the intended profile, bend conditions and coating adhesion requirements. A coating that performs on a flat sample must also tolerate the actual manufacturing process. Trial forming and a defined acceptance sample can be part of the applicable process-validation requirements.
Paint, colour and thickness describe separate properties
Specify the topcoat chemistry rather than assuming all coloured coil is the same. Polyester, silicone-modified polyester and PVDF-based systems can have different performance requirements; the exact formulation and supplier specification still matter. Record primer, topcoat and back-coat requirements separately.
Use a colour reference plus an approved physical sample where appearance is important. A screen colour or photograph is not an acceptance standard. Agree gloss, colour tolerance and batch consistency for panels that will sit next to each other.
State whether the stated steel thickness means base metal thickness or total coated thickness. Include dimensional tolerances rather than relying on the nominal figure alone. This avoids comparing a thinner substrate with a heavier coating against a thicker substrate with a different coating system.
Properties of the complete coating system
- Intended application and environmental exposure.
- Applicable product standard and edition, substrate grade and required mechanical properties.
- Metallic coating type and mass designation.
- Base metal thickness, width, tolerances, coil inner diameter and coil mass range.
- Pretreatment, primer, topcoat and back-coat specifications.
- Colour reference, gloss and agreed visual sample.
- Forming, adhesion or other inspection requirements appropriate to the project.
- Inspection documents and batch identification.
For color coated steel coil, the product form does not establish the complete coating system. The Z275 vs G90 coating-mass comparison explains the underlying zinc-coating terminology.
Coating names do not establish batch properties
Two coils with the same trade abbreviation can differ in dimensions, grade, metallic coating and paint system. Those differences matter when assessing whether they are suitable for the same use.
The steel mill certificate inspection guide explains how documents relate to batch identification. A product name alone does not establish the properties or certification of a specific coil.
