Steel Journal

Galvanized Square Tube Sizes: Dimensions and Wall Thickness

Read square-tube outside dimensions, wall thickness and length. Compare inch and metric notation and separate tube dimensions from zinc-coating requirements.

Nov 15, 2026Tianjin Huaqi Steel

Galvanized square tube sizes are described by the outside width × outside height × wall thickness, followed by the required length. A square section has equal outside dimensions; a rectangular section does not. For example, 50 × 50 × 2.0 mm identifies a square section with a nominal 2.0 mm wall, but it does not specify the piece length, steel grade or zinc coating. Outside dimensions alone therefore do not define the complete product.

Back to blog
IN THIS ARTICLE

Examples of galvanized square tube sizes

The following inch-based examples appear in LP Tube's published galvanized square tubing chart, checked on 15 November 2026. They illustrate catalogue combinations, not a universal size standard or an approved structural selection.

Examples of galvanized square tube sizes
Outside dimensions (inches) Nominal wall (inches)
1 × 1 0.060
1.5 × 1.5 0.083
2 × 2 0.060
2 × 2 0.083
2 × 2 0.120
4 × 4 0.120

A 2-inch outside dimension is 50.8 mm, not 50 mm. Likewise, 0.060 inch converts to 1.524 mm. Conversion helps read a drawing; it does not make a nearby metric catalogue size interchangeable. The actual size combination, tolerances and piece length remain separate dimensions to identify.

What to include in a galvanized square tube size specification

A useful size description has four separate measurements:

What to include in a galvanized square tube size specification
Field Definition
Outside dimensions Both external side dimensions, with units
Wall thickness Nominal thickness and the applicable tolerance requirement
Piece length Required length and any cutting tolerance
Quantity Pieces per size, or tonnage with the required size breakdown

The 50 × 50 × 2.0 mm example explains the notation. It does not establish suitability for a load-bearing application.

Do not assume that a smaller section is suitable because its wall is thicker. Structural suitability depends on the design, loading, connections and applicable project requirements, not the size label alone.

Why the outside size is not enough

Two tubes with the same outside dimensions can have different wall thicknesses, weights and suitability for fabrication. Equal outside dimensions do not establish equal cross-sectional area or mass.

Nominal wall thickness in millimetres or decimal inches is more explicit than a gauge number without an identified gauge system. If a drawing uses inches, keep that dimension explicit and confirm the proposed metric alternative. A nearby metric size is not automatically an acceptable substitute.

For rectangular tube, write both side dimensions. Also state whether orientation matters in the fabrication drawing. Square and rectangular sections need distinct dimensional descriptions.

Separate the tube specification from the coating specification

“Galvanized” describes a zinc coating, but it is not a complete steel grade or product specification. The tube may be made from pre-galvanized strip or galvanized after tube manufacture or fabrication; those are different process routes. Confirm how the internal surface, weld seam and any subsequently cut or welded areas are addressed.

Specify the coating requirement and its measurement basis. Coating mass and coating thickness are different quantities; do not compare their numbers without the units and the applicable specification. The required coating can also depend on the product and steel thickness, so avoid treating one coating value as suitable for every square tube.

Where ASTM A123 applies to batch-galvanized pipe or tube, its Pipe and Tubing category is relevant even when the tube has a structural use. Do not select a different material category solely because the finished assembly is structural. The applicable standard and project requirements govern this classification.

Dimensions, mass and material records

For galvanized square steel tube, dimensions, nominal wall, length, steel grade, manufacturing route and coating requirement are separate product characteristics.

Theoretical and measured mass are different values. A generic size chart does not establish the actual mass of a particular tube or bundle; packaging and other included items also change gross mass.

Material test documentation has to correspond to the identified material. A catalogue description alone is not a test certificate for a particular bundle. The mill test certificate guide explains the traceability checks.

Is there one standard galvanized square tube size chart?

No single catalogue chart establishes every size or every acceptable application. A chart describes its own listed combinations. The applicable material and dimensional specifications, coating requirements and engineering design determine whether a particular section is suitable.

Related reading